HamAntCal App Icon

HamAntCal

Utilities • State Road 41 Apps LLC
4+ v3.5 Recorded price: $0.99 App Store →
★★★★★
★★★★★
(57 App Store ratings)
🏆 Best: #13 Paid (HKG)
IPA Analysis
Technical Specs
Bundle ID com.Garber.HamAntCal
Version 3.5
App Store Size 1.62 MB
Minimum iOS 13.0
Devices iPhone, iPad, iPod touch
Catalog release date 2012-07-05
Latest recorded version date 2020-06-29
Features & Support
Advisory 4+
Languages (1)
EN
Top In App Purchases
No In App Purchases Listed

Preview

HamAntCal screenshot 1 HamAntCal screenshot 2 HamAntCal screenshot 3 HamAntCal screenshot 4

Description

HamAntCal Version 3.5 (Ham Antenna Calculator) will simply and intuitively calculate for you the starting length needed for constructing your antennas in feet/inches or in metric. It will calculate the starting length for "Dipole's", "Inverted Vee's", "Vertical's" and has a page for calculating 1/8, 1/4, 1/2, 5/8 and "Full Wave" length. In this update: ▪HamAntCal has been updated to 64 bit and iPhone X ▪New updated interface and settings menu ▪New in app purchase to update features ▪This update requires iOS 8.2 and above. --------------------------------------- ▪ HamAntCal works in feet/inches as well as metric. ▪ The easy to use and intuitive interface makes it easy to calculate starting lengths for building your antennas. It will calculate the starting length for "Dipoles", "Verticals" and "Inverted Vee" antennas. There is also a page for calculating 1/8, 1/4, 1/2, 5/8 and "Full Wave" length. ▪ I have come across a lot of different and conflicting information for calculating the length of an "Inverted Vee" antenna. Some say subtract 2 to 5 percent based on the angle of the wires. Others say to add a percentage based on the angle of the wires down from horizontal. I decided to test this before releasing this app. First I calculated for a "Dipole" using the "Dipole" calculator. Then I put together a "Dipole" with a support for the center insulator as well as the ends. I measured the resonant frequency with an antenna analyzer. Then I brought the ends down towards 45 degrees from horizontal. As the ends were lowered the resonant frequency increased. This means that the length of the "Inverted Vee" would need to be increased to stay resonant at the same frequency as the dipole. The "Inverted Vee" calculator has a slider that starts up with an angle of 45 degrees and can be adjusted down to 20 degrees continuously re-calculating as it is moved. This corresponds to about 4.5 to 2 percent added to the length of the "Inverted Vee". ▪ No antenna calculator can give exact results in every case. Much will depend on the wire used, the height above ground, the ground itself, nearby objects, etc…. It's always a good practice to add a little extra wire and then trim up to the desired frequency. ▪ This calculator will calculate from 30 Khz to 500Mhz for the "Dipole", "Vertical" and "Length" calculators. The maximum for the "Inverted Vee" calculator is 60MHz. ▪ This calculator does not give exact measurements and the results will need to be trimmed using an antenna analyzer or SWR meter to the exact frequency after installation. Leave some extra wire on each section for trimming and wrapping around the insulators. ▪ Keep in mind that there are a lot of factors that can affect the resonant frequency of an antenna. At VHF and above even a small change in the length or diameter of an element can make a large change in the resonant frequency of an antenna even more so than at lower frequencies. This calculator just provides the starting length for building an antenna and proper matching methods will need to be used. ▪ Please be safe while building your antennas. Always use the proper safety equipment. Never build your antenna where it can come in contact with power lines, this includes the supports as well as the antenna itself and feed lines. BE SAFE! ▪ Although I have had good results using this calculator the results are not guaranteed. Always add some extra length and trim the antenna to frequency (it's much easier to trim than it is to add wire to the antenna). Please feel free to contact me with suggestions, problems, compliments, ideas for improvements or additions to HamAntCal. Your ratings are appreciated.

What's New

Version 3.5 2020-06-29
General updates for IOS 13 and interface cleanup.

Technical Analysis

Package Overview Basic metadata
Bundle ID com.Garber.HamAntCal
Current Version 3.5
Minimum iOS 13.0
Package Size App Store Size
Package Metadata 0 / 3 version records
4.5 / 5.0 (55 ratings)
Detailed binary, privacy manifest, framework, and Info.plist results have not been indexed for this package yet. The verified App Store and archive metadata above remains available.

Known Version Records

0 version records with stored package metadata • 3 known version records

Stored metadata does not guarantee a package is currently available to download.

Archived versions of HamAntCal
Details Version / IDs Version date Action
HamAntCal icon
Not archived
App Store ID: 836617830 Unknown Paid / Arcade
HamAntCal icon
Not archived
App Store ID: 823729054 Unknown Paid / Arcade
HamAntCal icon
Not archived
App Store ID: 9256810 Unknown Paid / Arcade