Preview
Description
All the everyday calculations for electrical design, in one app. When you're designing a circuit, small questions keep coming up: "Will this resistor pair give me the voltage I need?" "What's the rise time of this RC circuit?" "What do three resistors in parallel add up to?" "Where is the cutoff frequency of this filter?" "Which resistors give this amplifier a gain of 10?" "What resistor do I need for 10 mA through this LED?" "What value is this resistor with these color bands?" "What is 0x3F8 in binary?" Too small to open a spreadsheet, but you want the answer right now. EL tools is a practical calculator for electrical design that lets you check these things quickly on your phone. ■ Voltage Divider Enter the input voltage and target output voltage, choose a standard resistor series (E6/E12/E24/E48), and instantly find the R1/R2 combinations closest to your target. The min/typ/max output voltage is shown for each combination, taking resistor tolerance (and input voltage tolerance) into account. Useful for power supplies, voltage references, and ADC inputs. ■ RC Step Response Calculate the time constant τ = RC from the resistance and capacitance. View the rise (charge) or fall (discharge) curve as a graph, and check the voltage at any elapsed time with a slider. Handy for reset, delay, and smoothing circuits. ■ Combined Resistance and Capacitance Supports series and parallel connections. Calculate the nominal, minimum, and maximum combined value from up to three resistors or capacitors and their tolerances. ■ Filters Supports low-pass (RC/RLC), high-pass (RC/RLC), band-pass (RLC), and pi (CLC) filters. See the cutoff frequency, damping ratio, or the band-pass center frequency, Q, and bandwidth, with the frequency response shown as a Bode plot. Check a pi filter from its values, or design a 3rd-order Butterworth pi filter from a target cutoff and resistance. ■ Op-Amp Gain Choose an inverting or non-inverting amplifier, enter the target gain, and find the closest Rf/Rg combinations from a standard resistor series (E6/E12/E24/E48). The min/typ/max gain is shown for each combination, taking resistor tolerance into account. ■ LED Current-Limiting Resistor Get a standard resistor value from the supply voltage, LED color or Vf, target current, and number of LEDs in series. See the min/typ/max current with tolerances, the resistor power, and a suggested rating. If the supply is too low, the app tells you how many LEDs it can drive and the voltage you need. ■ Parts Read resistor color codes (4 or 5 bands), or look up the colors for a value. Decode chip resistor markings (3-digit, 4-digit, R notation, EIA-96), and check a chip size table with metric and inch codes, dimensions, and typical power ratings. ■ Programmer Calculator Convert values between HEX, DEC, OCT, and BIN at a glance. Tap individual bits to toggle them, and choose the word size (8/16/32/64-bit) and signed (two's complement) or unsigned. Run bitwise operations (AND, OR, XOR, NAND, NOR, NOT, shifts, rotates) and arithmetic, then feed the result back in to keep going. ■ Useful for - Checking values while designing circuits - Choosing resistor and capacitor values - Designing voltage dividers for power circuits - Checking RC delay times and filter cutoff frequencies - Choosing gain resistors for op-amp circuits - Choosing current-limiting resistors for LEDs - Identifying the resistors on your bench - Working with register values and bit masks in firmware - Electronics hobby projects and learning circuits Quick answers for those "let me just calculate this" moments. Not complex enough for a full simulation, but you still want the result on the spot. EL tools supports your day-to-day electrical design work with simple, straightforward controls.
What's New
Version 1.4 2026-11-03
- New: LED Resistor. Get a standard resistor value from the supply, Vf, current, and number of LEDs, with min/typ/max current and resistor power. - New: Parts. ...- New: LED Resistor. Get a standard resistor value from the supply, Vf, current, and number of LEDs, with min/typ/max current and resistor power. - New: Parts. Read resistor color codes and chip resistor markings, and look up chip sizes. - Filters: added high-pass, band-pass, and pi filters. Design a pi filter from a target cutoff. - Combined: now calculates capacitors as well as resistors. - Circuit diagrams and formulas on the Divider, Transient, Combined, Filter, and LED tabs. - The tab bar now scrolls sideways to fit all 8 tools. Technical Analysis
Package Overview Basic metadata
Bundle ID
com.kazeellegard.eltools Current Version 1.4
Minimum iOS 15.0
Package Size App Store Size
Package Metadata 0 / 0 version records
Detailed binary, privacy manifest, framework, and Info.plist results have not been indexed for this package yet. The verified App Store and archive metadata above remains available.
Developer Information
Known Version Records
0 version records with stored package metadata
Stored metadata does not guarantee a package is currently available to download.
| Details | Version / IDs | Version date | Action |
|---|